Michael Hanslip Coaching

If you want to go faster, you have to pedal harder

Chain lubricating practices

In a Facebook group on cycling, I recently got into an argument about the best way to lubricate a chain.
 
I stated a simple enough message. That frequent lubrication is the pathway to a quickly worn-out chain; probably faster than any other option. I've seen it first hand and I can support it with a mechanism. When I worked in a bike shop we had numerous customers who only took away the message that they needed to lubricate their chain. So they did. Some after every ride.
Particularly back when I worked in a bike shop, there were more bad options than good ones for lubricant. Any "oil" is a prime candidate for rapid wear. The problem isn't the lubricating properties of the oil itself. After all, motor oil keeps a very complicated internal combustion engine running for hundreds of thousands of kilometres. The problem is that it is sticky; a characteristic that helps it do its job inside the confines of an engine. But one that confounds its role on a bike chain. We ride around in the outdoors where there is all manner of fine dust and grit that sticks to the sticky oil. Look at just about any bike chain that has some use, it has some dirt stuck to the outside.
The problem arises when more oil is applied. It washes that dirt from the outside (where it does no harm) to the inside - the moving surfaces of the chain (where it can do a great deal of harm).
Grinding paste (such as for making a glass lens, or polishing a nice stone, or a concrete floor) is essentially some fluid (like the oil) and some grit (like that stuff stuck to a chain).
Once inside the chain, every time the chain bends around a chainring or cassette, it is being abraded by the paste.
I've seen a chain go from new to beyond worn in as little as 600 km due to frequent lubrication.
You'd get markedly better life just from a good wipe of that dirt prior to re-lubing.
This is where the bike industry tried to outsmart the dirt (not that the dirt is actually smart - just ubiquitous) with self cleaning lubricants. Early ones didn't work so well. The cleaning part of the mix attacked the lubricating part so it required frequent reapplication, sometimes in the middle of a ride. Eventually the chemists came up with some formulae that worked. I used Rock N Roll Gold for at least a decade with great results. Good lifespan for the drivetrain, low effort on my part, good shifting and didn't run out in the middle of a ride. It wasn't so much self cleaning as easy cleaning.
When I was a kid there were some cyclists I knew who dipped their chain in melted paraffin wax. Because the wax dried hard, and it was waxy, nothing stuck to the chain. And it didn't run or splatter in use. Unfortunately, it wasn't a great lubricant and it couldn't mobilise inside the chain. Once the wax on the articulating surfaces inside the chain was worn away, it was time to redip the chain. Most lubricants are runny enough to continually replenish the moving surfaces with fresh stuff in use. [Interesting little aside here, if you take a chain link and place it on top of a drop of liquid and bend the chain side to side, the motions of the pieces will suck up the liquid and push it out the top - chains in use do this all the time.]
Waxing is back. But now it is not simply paraffin wax, but some clever chemists have added numerous extra goodies to the waxy stuff so that it provides good lubrication for your chain. Silca even makes a specific bike chain station with hanging arm so you can simply immersion-wax a chain.
While chemists were playing with waxes, several came up with an emulsified option (if you've ever used oil & vinegar dressing you'll have noticed that oil and water don't mix - the best science can offer us is a liquid where the oil is held in the water in extremely tiny droplets: an emulsion). These emulsified waxes can be dripped onto the chain, the water penetrates (some more than others - more on that in a minute), delivering the waxy lubricant inside the chain where it can do some good. Eventually the water evaporates and the only thing left behind is the desired wax.
As I wrote above, I used Rock N Roll for about a decade. I got a sample bottle of Squirt at a bike race in my goody bag. I tried it on a few MTB rides and found it was good. I went through a couple of bottles of Squirt before I learned that Smoove was similar, but better. They provide good shifting and easy application along with low dirt. But not the best lifespan for chains because whatever solvent they use to get the wax into suspension isn't drawn into the chain as easily as one might like.
Zero Friction Cycling tests chains to destruction. They have established a protocol of clean then dirty use that tests either chains or lubricants for effectiveness. Both Squirt and Smoove do better in the testing after a period - where the lubricant finally makes its way inside. I'm not sure how much it helped, but whenever I applied one after learning about this, I used a heat gun to warm up the chain and help mobilise the lube inside.
Two lubricants that perform better than the Squirt/Smoove twins are also a bit of twinsies themselves: Silca Super Secret drip wax and Effetto Mariposa flowerpower drip wax. Both test well at Zero Friction and behave similarly in my garage testing. Because the solvent is water for both of them, it runs into the chain "just like water".
I had the pleasure of talking to Josh Poertner from Silca for about an hour online when I was reviewing some Silca products. Josh puts out loads of YouTube videos about Silca products and about best practices he and his team have found. Josh tells me that SSS wax is about 70% wax and 30% water. Thus, on one application, I add a drop of SSS to each roller on the chain and pedal backwards a little to draw the suspension inside the chain. Then I leave it for a day. The water evaporates leaving behind 70% wax fill and 30% voids. A second application will fill those voids with emulsion and evaporate once again. Only this time the chain is 91% full of wax. A third application (a bit of overkill without a  lot of pay-off in my testing) leaves the chain about 98% full of wax. Which is about the same as immersion waxing with the Silca hot wax which is the same formula as the drop wax in a different format.
 
The wax in these four lubricants is not sticky. It doesn't promote grit sticking to the chain. But some sticks anyway.
I can't be bothered doing a full re-wax every time the chain requires a top-up. Instead I wipe the chain as much as I can such that it appears clean (I know some grit is lurking in places I can't wipe) and then drip on some more wax. A single top-up will almost double the interval between cleanings. I know it is speeding up the wear rate on my chain slightly, but in a return on investment (of time or money) I think it's OK.
The beauty of the waxy chain is that it can be completely removed with some boiling water. This was Josh's idea and it is brilliantly simple. Chain on big ring. Bike in work stand. Full kettle of boiling water. Move chain backwards, pour hot water on chainring. Two minutes later you have an incredibly clean chain with some water in it. I suspect drying it out first would fully load the chain with the 70% wax load, whereas dripping water onto an already wet chain won't displace all the water with waxy water [editorial note - I noticed Zero Friction Cycling expressly demands drying out the chain after the cleaning step, so I will have to revise my approach in future]. But it is much easier that way and I don't have so many days to relubricate a bike I use every day to ride to work.
If I do the boiling water thing on Saturday morning, the second lubrication on Sunday morning, I can ride a silent bike to work on Monday morning.
It is even simpler with any other bike in the quiver - they don't get ridden so often so the cleaning and lubricating can take place over a week or more.
 
The proof, they say, is in the pudding. My Campagnolo 12-spd chain that never got lubricated when dirty according to the above (but not the boiling water clean as I didn't know about that then) had 13000 km on it when I retired it. I wouldn't have done so were I not replacing the frame. It wasn't worn out yet, just very worn. The Campag 12-spd chain on my race bike only has 3500 km on it to date, but it measures "new" because it rarely gets ridden in wet conditions and that's when a lot of wear occurs. Now that I have Red 12-spd on my commuter, I'm at 6000 km and can't accurately measure any wear on the chain (it might be half the thickness of the scribe marks on my metal 12" ruler). I have heard of Red chains worn out in 4000-5000 km. At this rate I should get at least 12000. Wear is not linear in chains, once you go through the surface hardening it speeds up quickly.
On my various mountain bikes, the chains (all SRAM, mostly 12-spd - the DH bike is 7-spd but that is actually an 11-spd chain) last crazy amounts of time. And if we look at Zero Friction chain wear statistics, the Eagle chain is about the longest lasting chain ever tested. Couple a long-lasting chain with careful lubrication and they last almost forever.
Which brings me back to where I started. Some guy got angry with me for suggesting that frequent lubrication leads to premature wear. It doesn't have to. But it routinely does.
My old boss at the bike shop used to counsel lazy customers to not lube their chain at all. Better dry than worn out he used to offer. He had a deal with one customer who rode the most of anyone we knew - 600-1000 km per week most weeks. That's pro sorts of distances. He offered her free service for the life of her bike if she promised to never do anything to her bike. And after that deal was accepted, she went from a chain per week to a few per year.
Thus I stand by my statement. Lubricate a dirty chain at the peril of your pocketbook.